/**
  @Generated PIC10 / PIC12 / PIC16 / PIC18 MCUs Source File

  @Company:
    Microchip Technology Inc.

  @File Name:
    mcc.c

  @Summary:
    This is the mcc.c file generated using PIC10 / PIC12 / PIC16 / PIC18 MCUs

  @Description:
    This header file provides implementations for driver APIs for all modules selected in the GUI.
    Generation Information :
        Product Revision  :  PIC10 / PIC12 / PIC16 / PIC18 MCUs - 1.65
        Device            :  PIC16F18855
        Driver Version    :  2.00
    The generated drivers are tested against the following:
        Compiler          :  XC8 1.45 or later
        MPLAB             :  MPLAB X 4.10
*/

/*
    (c) 2016 Microchip Technology Inc. and its subsidiaries. You may use this
    software and any derivatives exclusively with Microchip products.

    THIS SOFTWARE IS SUPPLIED BY MICROCHIP "AS IS". NO WARRANTIES, WHETHER
    EXPRESS, IMPLIED OR STATUTORY, APPLY TO THIS SOFTWARE, INCLUDING ANY IMPLIED
    WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY, AND FITNESS FOR A
    PARTICULAR PURPOSE, OR ITS INTERACTION WITH MICROCHIP PRODUCTS, COMBINATION
    WITH ANY OTHER PRODUCTS, OR USE IN ANY APPLICATION.

    IN NO EVENT WILL MICROCHIP BE LIABLE FOR ANY INDIRECT, SPECIAL, PUNITIVE,
    INCIDENTAL OR CONSEQUENTIAL LOSS, DAMAGE, COST OR EXPENSE OF ANY KIND
    WHATSOEVER RELATED TO THE SOFTWARE, HOWEVER CAUSED, EVEN IF MICROCHIP HAS
    BEEN ADVISED OF THE POSSIBILITY OR THE DAMAGES ARE FORESEEABLE. TO THE
    FULLEST EXTENT ALLOWED BY LAW, MICROCHIP'S TOTAL LIABILITY ON ALL CLAIMS IN
    ANY WAY RELATED TO THIS SOFTWARE WILL NOT EXCEED THE AMOUNT OF FEES, IF ANY,
    THAT YOU HAVE PAID DIRECTLY TO MICROCHIP FOR THIS SOFTWARE.

    MICROCHIP PROVIDES THIS SOFTWARE CONDITIONALLY UPON YOUR ACCEPTANCE OF THESE
    TERMS.
*/ 

// Configuration bits: selected in the GUI

// CONFIG1
#pragma config FEXTOSC = XT    // External Oscillator mode selection bits->XT (crystal oscillator) above 500kHz, below 4MHz; PFM set to medium power
#pragma config RSTOSC = EXT1X    // Power-up default value for COSC bits->EXTOSC operating per FEXTOSC bits
#pragma config CLKOUTEN = OFF    // Clock Out Enable bit->CLKOUT function is disabled; i/o or oscillator function on OSC2
#pragma config CSWEN = ON    // Clock Switch Enable bit->Writing to NOSC and NDIV is allowed
#pragma config FCMEN = ON    // Fail-Safe Clock Monitor Enable bit->FSCM timer enabled

// CONFIG2
#pragma config MCLRE = ON    // Master Clear Enable bit->MCLR pin is Master Clear function
#pragma config PWRTE = OFF    // Power-up Timer Enable bit->PWRT disabled
#pragma config LPBOREN = OFF    // Low-Power BOR enable bit->ULPBOR disabled
#pragma config BOREN = ON    // Brown-out reset enable bits->Brown-out Reset Enabled, SBOREN bit is ignored
#pragma config BORV = LO    // Brown-out Reset Voltage Selection->Brown-out Reset Voltage (VBOR) set to 1.9V on LF, and 2.45V on F Devices
#pragma config ZCD = OFF    // Zero-cross detect disable->Zero-cross detect circuit is disabled at POR.
#pragma config PPS1WAY = ON    // Peripheral Pin Select one-way control->The PPSLOCK bit can be cleared and set only once in software
#pragma config STVREN = ON    // Stack Overflow/Underflow Reset Enable bit->Stack Overflow or Underflow will cause a reset
#pragma config DEBUG = OFF    // Background Debugger->Background Debugger disabled

// CONFIG3
#pragma config WDTCPS = WDTCPS_31    // WDT Period Select bits->Divider ratio 1:65536; software control of WDTPS
#pragma config WDTE = OFF    // WDT operating mode->WDT Disabled, SWDTEN is ignored
#pragma config WDTCWS = WDTCWS_7    // WDT Window Select bits->window always open (100%); software control; keyed access not required
#pragma config WDTCCS = SC    // WDT input clock selector->Software Control

// CONFIG4
#pragma config WRT = OFF    // UserNVM self-write protection bits->Write protection off
#pragma config SCANE = available    // Scanner Enable bit->Scanner module is available for use
#pragma config LVP = OFF    // Low Voltage Programming Enable bit->High Voltage on MCLR/Vpp must be used for programming

// CONFIG5
#pragma config CP = OFF    // UserNVM Program memory code protection bit->Program Memory code protection disabled
#pragma config CPD = OFF    // DataNVM code protection bit->Data EEPROM code protection disabled

#include "mcc.h"


void SYSTEM_Initialize(void)
{
    PMD_Initialize();
    PIN_MANAGER_Initialize();
    OSCILLATOR_Initialize();
    ADCC_Initialize();
}

void OSCILLATOR_Initialize(void)
{
    // NOSC EXTOSC; NDIV 1; 
    OSCCON1 = 0x70;
    // CSWHOLD may proceed; SOSCPWR Low power; 
    OSCCON3 = 0x00;
    // MFOEN disabled; LFOEN disabled; ADOEN disabled; SOSCEN disabled; EXTOEN disabled; HFOEN disabled; 
    OSCEN = 0x00;
    // HFFRQ 4_MHz; 
    OSCFRQ = 0x02;
    // HFTUN 32; 
    OSCTUNE = 0x20;
}

void PMD_Initialize(void)
{
    // CLKRMD CLKR enabled; SYSCMD SYSCLK enabled; SCANMD SCANNER enabled; FVRMD FVR enabled; IOCMD IOC enabled; CRCMD CRC enabled; NVMMD NVM enabled; 
    PMD0 = 0x00;
    // TMR0MD TMR0 enabled; TMR1MD TMR1 enabled; TMR4MD TMR4 enabled; TMR5MD TMR5 enabled; TMR2MD TMR2 enabled; TMR3MD TMR3 enabled; NCOMD DDS(NCO) enabled; TMR6MD TMR6 enabled; 
    PMD1 = 0x00;
    // ZCDMD ZCD enabled; DACMD DAC enabled; CMP1MD CMP1 enabled; ADCMD ADC enabled; CMP2MD CMP2 enabled; 
    PMD2 = 0x00;
    // CCP2MD CCP2 enabled; CCP1MD CCP1 enabled; CCP4MD CCP4 enabled; CCP3MD CCP3 enabled; CCP5MD CCP5 enabled; PWM6MD PWM6 enabled; PWM7MD PWM7 enabled; 
    PMD3 = 0x00;
    // CWG3MD CWG3 enabled; CWG2MD CWG2 enabled; CWG1MD CWG1 enabled; MSSP1MD MSSP1 enabled; UART1MD EUSART enabled; MSSP2MD MSSP2 enabled; 
    PMD4 = 0x00;
    // DSMMD DSM enabled; CLC3MD CLC3 enabled; CLC4MD CLC4 enabled; SMT1MD SMT1 enabled; SMT2MD SMT2 enabled; CLC1MD CLC1 enabled; CLC2MD CLC2 enabled; 
    PMD5 = 0x00;
}


/**
 End of File
*/